5. Place construction adhesive on the back of each piece of quarter round, then press it into place against the wall (adhesive should come out slightly from under each piece). If using glue, wait about 30 minutes for it to set before proceeding to step 6. If not using glue, go ahead and proceed to step 6. Note: You can also use finishing nails instead of construction adhesive if desired (see below). However, be aware that this method is not as secure and could potentially cause your quarter rounds to come loose over time if not installed correctly. It is also important that your wall surface be smooth before installing quarter round with nails, as any bumps or irregularities will be visible once the trim is in place.
6. To secure the quarter round in place without using nails, use a heavy-duty stapler and staples that are at least 1 1/4 inches long. Space the staples about 6 inches apart along the length of each piece of quarter round.
7. To finish, caulk the seams where the quarter round meets the baseboard and paint or stain as desired.
Installing quarter round without a nail gun is possible, but it does require a few more tools and a bit more time. Here are the steps:
1. Cut the quarter round to size with a miter saw or hand saw.
2. Dry fit the quarter round into place to make sure it fits properly.
3. Mark the locations of each stud on the wall so you know where to nail into.
4. Pre-drill holes through the quarter round at each stud location using a drill bit slightly smaller than your nails. This will help prevent splitting when you drive the nails in later.
5. Place construction adhesive on the back of each piece of quarter round, then press it into place against the wall (adhesive should come out slightly from under each piece). If using glue, wait about 30 minutes for it to set before proceeding to step 6. If not using glue, go ahead and proceed to step 6. Note: You can also use finishing nails instead of construction adhesive if desired (see below). However, be aware that this method is not as secure and could potentially cause your quarter rounds to come loose over time if not installed correctly. It is also important that your wall surface be smooth before installing quarter round with nails, as any bumps or
Step 1: Cut molding
Some people like the look of quarter round molding, but they don’t want to use a nail gun to install it. Here’s how you can install quarter round molding without a nail gun.
1. Cut the molding to size using a miter saw or other type of saw. Make sure the cuts are clean and precise.
2. Apply construction adhesive to the back of the molding, being generous with it so that it will hold well.
3. Press the molding into place against the wall or other surface you’re installing it on. Use clamps or weights to hold it in place while the adhesive dries (follow the manufacturer’s instructions for drying times).
Step 2: Lay molding against wall, flush with the floor
If you’re not using a nail gun, the process for installing quarter round molding is similar to that of baseboard molding. Begin by measuring and cutting your molding to size, then use a miter saw to cut 45-degree angles on the ends. Once your molding is cut, lay it against the wall with the flat edge against the floor. Use a level to make sure it’s flush with the floor, then mark where you’ll need to make your cuts. Make your cuts on the marked lines, then fit the pieces together and secure them in place with finishing nails.
Step 3: Hammer your finishing nail almost all the way into the wall
If you’re installing quarter round without a nail gun, the first thing you’ll need to do is mark out where your trim will go. Once you’ve done that, it’s time to start nailing.
Start by hammering your finishing nail into the wall almost all the way. Then, holding the quarter round in place, finish driving the nail into the wall. Repeat this process until all of your quarter round is installed.
Step 4: Use the nail set to drive the nail the rest of the way in
If you don’t have a nail gun, don’t worry! You can still install quarter round without one. Just follow these simple steps:
1. Cut your quarter round to size. Use a miter saw or hand saw to cut the molding at a 45 degree angle. Remember to measure twice and cut once!
2. Pre-drill holes in the quarter round. This will make it easier to drive the nails in later.
3. Apply wood glue to the back of the quarter round and position it against the wall where you want it installed. Use painters tape or masking tape to hold it in place while the glue dries (about 30 minutes).
4
Step 6: Cover nail heads
If you’re using quarter round that’s already been cut to size, simply fit it in place and tap it gently into place with a rubber mallet. If you’re cutting the molding yourself, use a miter saw set at 45 degrees to make your cuts.
Once the quarter round is in place, use a nail set to sink any nails below the surface of the molding. Fill any holes with wood filler, let it dry, then s and the area smooth.